Hardware
OEM Equipment
This is a listing of OEM Board Power Supply manufacturers and vendors in a card form factor.
The products or devices the companies produce are listed under the
company name, in alphabetic order.
Related pages; the COTS cardS and, UPS page.
--------------------
The main
Power Supply Manufactures page
Medical Power Supply Manufactures page
Act/Techno
{Redundant VME Power Supply Manufacturer}
Advanced Conversion
Technology
{Rack Mounted VME, Custom Power Supply Manufacturer}
Bi Ra Systems
{VME High Voltage-CAMAC-NIM-FASTBUS-Corrector Magnet Driver-SCR Thyratron
Driver}
Digital Power Corp.
{3U/6U CompactPCI Power Supplies}
Dynaload "Transistor Devices Inc
'TDI'"
{Military grade VMEbus card Power Supply}
One Stop Systems Inc.
{3U/6U cPCI Power Supply Boards, Power supply backplane, dual P47, Uninterruptable power supply (UPS)}
-----------------
Rantec Power Systems Inc.
{VME and ATR Military Card Power Supplies. Convection and Conduction Cooled}
SL Power Electronics
{200 W in 3U x 8HP CompactPCI, 750 Watt Multiple Output VMEbus and Multbus II}
Top Microsystems
{1U, 2U, PS2, Redundant, Open Frame, CompactPCI, Adaptors, DC/DC, Custom}
Total Power International
Inc.
{PC104 - cPCI - U Bracket Power Supplies}
Vector Electronic Company
{3U Card Power Supply Manufacturer, M DIN Connector}
Wiener
{VME/VXI/CAMAC/NIM Card Power Supply}
Military Power Supply Standards:
MIL-STD-901D SHOCK TESTS. H.I. (HIGH-IMPACT)
SHIPBOARD MACHINERY, EQUIPMENT, AND SYSTEMS, REQUIREMENTS FOR
[Shock]
MIL-STD-167-1 MECHANICAL VIBRATIONS OF SHIPBOARD EQUIPMENT (TYPE 1
- ENVIRONMENTAL AND TYPE II - INTERNALLY EXCITED)
[Vibration]
MIL-STD-5400 ELECTRONIC EQUIPMENT, AEROSPACE, GENERAL
SPECIFICATION FOR [See MIL-HDBK-5400]
MIL-STD-810E ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND
LABORATORY TESTS [Humidity]
MIL-STD-46IE REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC
INTERFERENCE CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT
[EMI/EMC]
MIL-STD-704F AIRCRAFT ELECTRIC POWER CHARACTERISTICS
MIL-STD-1275B CHARACTERISTICS OF 28 VOLT DC ELECTRICAL SYSTEMS IN
MILITARY VEHICLES
NAVMAT P 4855 1A: Navy Power Supply Reliability
NAVSO P-3641A: Provides guidance in the design, test and
manufacturing [Replaced by NAVMAT P 4855 1A]
Commercial Power Supply Standards:
IEC-60950: Information technology equipment - Safety: General
requirements
IEC-950: Information technology equipment - Safety: [Replaced by
IEC-60950]
UL-60950:
UL 1950: [Replaced by UL-60950]
Medical-Grade Power Supply Standards:
IEC601-1: Medical electrical equipment: General requirements for
safety.
UL2601-1:
Power Supply Derating Guidelines:
Operating Temperature range is normally 0 to 50oC,
derate 20% for each additional 10oC increase above
50oC.
Operating Temperature range; 0oC to +70oC.
Full power to +50oC then derate 2.5%/oC to
+70oC. Or, derate linearly from 100% load @ 50oC to
75% @ 60, derated at 10% per oC to a Maximum of
+65oC
Forced air cooling [20CFM nominal]: a power supply may require a
forced air flow to operate at its rated maximum temperature rating.
Derate 20% with out cooling
Open Frame supplies: may require an additional 15% power de-rating
when covered by a frame.
About: The power supply specification should detail its operation,
use the above as a rule of thumb. Normal operational temperature range is
defined as ambient [Maximum].
A listing of OEM Electronic Power Supply Card Manufacturers and
vendors.
The products or power supplies the companies produce are
listed under the manufacturer name, in alphabetic order.
If the power
supply is produced in a circuit card form factor, for example cPCI, then you should also check
that
particular interface bus page or the COTS card manufacturers page.
{Power Supply Manufacturers top}
 | |||||||
| Home | |||||||
 |
 |
 |
 |
 |
 |
 |
 |
| Distributors | Components | Equipment | Software | Standards | Buses | Design | Reference |