Ribbon Fuse Manufacturer

Hardware
Mechanical Components

Fuse Holders



[Mechanical Fuse] [Passive Fuse]
[ Circuit Breaker] [Surge Protector]
[Fuse Holder]
[Home]

Fuse Holder Manufacturers

This is a listing of Fuse Holder manufacturers and Vendors. The types of products or devices they produce are listed under the company name.
The most commonly used mechanical fuse sizes are: 5mm x 20mm and 6.3mm x 32mm [1/4" x 1 1/4"].
A table of physical fuse sizes is provided after the manufacturers listing





Bussmann
{PCB Mount Fuseholder, Blade Type Holders, GMT Type, HBH}

Keystone Electronics Corp.
{Fuse Holders: 2AG, 5AG, 5mm, Automotive, Fuse Covers}

Littelfuse Inc.
{Panel Mount 2AG, 3AG Water Tight, Fuse Holders; Fuse Clips ATO, Gangable, In-Line, Fuse Blocks, LT-5}

Zierick Manufacturing
{Fuse Clip Terminals}

----------------------------




The most common panel mount fuse holder supports a 3AG fuse and requires a 'D' cut-out in the panel.
The cut-out is .475in ['D' side] x .502in [round]. A another common type of cut-out has a flat side on both the right and left side, .461 x .502
When selecting a fuse holder be sure that the holder can withstand the maximum fuse rating for voltage and current.
The fuse holder could melt trying to with stand the power dissipated by the fuse before the fuse opens.

Fuse Physical Sizes: [Common devices in Bold]
5mm x 20mm: .29" x .79"
1AG: 1/4" x 5/8"
2AG (5mm @ 15mm): .2" x .59"
3AG: 1/4" x 1 1/4"
4AG: 9/32" x 1 1/4"
5AG: 13/32" x 1 1/2"
7AG: 1/4" x 7/8"
8AG: 1/4" x 1"




Military Standards
MIL-F-5373D: Fuse Holder, Block Type, Aircraft
MS24000F: Fuse Holder, Block-Type, 1-, 2-, and 3-Pole, 1- to 30-Ampere, Aircraft
MIL-PRF-23419: Fuse, Cartridge, Instrument Type, General Specification for
Those MIL Specs have been cancelled, refer to Aerospace Standard AS53731
A-A-55504: Fuseholder, Extractor Post, Which Accommodates 3AG
MIL-PRF-19207; Fuseholders, Extractor Post Type, Blown Fuse, Indicating and Non-indicating, General Specification
MIL-F-15160D, MS15249

Fuse Holder Drawing per MIL-A-A-55504
Panel Mount Fuse Holder

Current Derating of a Fuse {Design tip}
Fuse operation in DC Circuits {Design tips}
Fuse Holder data {Design hints}
Block Fuse Holder {Graphic}

Fuse Holder Enclosure properties; Unsealed, Dripproof, Splashproof, Watertight,
Watertight with EMI/RFI shielding, Watertight and body sealed, or Water-tight and body sealed with EMI/RFI shielding
Fuse Enclosures may also be Non-indicating or Indicating [to signify a blown fuse].
Indicating Fuse Holders will be supplied with glow lamps, incandescent lamps, or white light emitting diodes (LED).

{Fuse Holder Manufacturer Index}

A listing of Fuse Holder Manufacturers and Vendors. The types of products or devices they produce are listed under the company name, in alphabetic order.
Additional component manufacturers may be found by selecting the Components icon below, or Equipment manufacturers may be found by selecting the OEM Equipment icon.

PC motherboard
Home

Distributor rolodex Electronic Components Electronic Equipment EDA CDROM Software Engineering Standards, BOB card Cabled Computer Bus Electronic Engineering Design Table Conversion DB9-to-DB25.
DistributorsComponents Equipment Software Standards Buses Design Reference
Modified 3/17/12
© 1998 - 2016 All rights reserved Larry Davis